Search results

NOT mine, btw! http://pittsburgh.craigslist.org/mcy/2944723000.html

Not my stuff, just trying to help out. Mount Pleasant is located southeast of Pittsburgh, PA. http://pittsburgh.craigslist.org/mcy/2900908413.html

My Warrior has found its way to a new home. I passed on the airhead KDX trade, but it's almost too nice to leave. It went to a good home that I visit often while at work. The owner's pretty picky, and I'm sure it wont get thrashed. :tup: I'll be on the lookout for another, after I get back up...

Local craigslist find, NOT MINE: Just tryin' to help a brutha out. http://pittsburgh.craigslist.org/rvs/2768700804.html

Found this while poking around dirtbike stuff. Anybody try this on a Warrior stator yet? http://kdxrider.net/forums/viewtopic.php?t=10226&sid=2e4b5c31cc0c5b5428f28869e69f7e40

It's the cam on the right in the pic. It has minor rust pitting on the lobes that can barely be felt with a fingernail. The pic makes them look a lot worse and like the lobes are worn flat-edged, but it's not. I'd guess with emery cloth and a cotton bench buffer they'd polish up OK. Pin is...

None are mine. May be some potential good deals for parts or rebuilds: http://pittsburgh.craigslist.org/rvs/2581762308.html http://pittsburgh.craigslist.org/rvs/2600810514.html http://pittsburgh.craigslist.org/rvs/2607238226.html http://pittsburgh.craigslist.org/rvs/2603338541.html Here's a...

NOT MINE, found in local Pittsburgh craigslist. My garage is so full now I can't put a toothpick in it, so I'm passing it on: http://pittsburgh.craigslist.org/mcy/2553145204.html .

Or trade?? Enduro/4 stroke/2 stroke... http://pittsburgh.craigslist.org/mcy/2532242734.html

May be a dumb question but... the stock anti vibration rubber dampers between the cooling fins... Without them, running the quad in the garage I can hear all of the monkey movement in the top end (bike is stock). I have no problem with it, as I don't hear anything abnormal. I suspect the...

Looking to install an oil pressure gauge. I removed the bolt in the top right rear of the cylinder head, and found it to be a stock banjo bolt! That eliminates one concern. Now I just need a fitting and another crush washer to install the line. Any ideas for locating a fitting? Bolt is 6mm OD...

Don'tcha just hate it when you have leftover parts after a build? Well, I'm not done with it, but need to know some things. Where the cylinder meets the case, on the bottom right corner (oil galley head bolt hole, at the base gasket), is there a rubber "sleeve" shaped seal AND an O-ring that go...

Need a stock cam for my '93.

FINALLY got off my butt and attempted to complete my cylinder head "project" today. Anybody have any REAL WORLD experience with a pitted cam (on any engine)? Lobes had what appeared to be VERY minor rust spots. Wiped them with some red Scotchbrite, and the pits are minor but numerous on the...

Not technically ATV parts, but... Was a spare from an '86 RM125G that I used to have. Measures approx. 16.5" eye to eye, uses approx. 3/8" bolts. Don't know if anyone can use it for their Warrior or other? It is rebound, compression, and spring preload adjustable. Lower plastic adjuster knob...

I removed the reverse linkage to paint the engine, but didn't look to see how it went together. I have the parts assembled in the correct order per the online microfiche diagram. Question is, do both ends of the spring go into the slot in the black shifter "plate" on the engine case? Does that...

Converting my '93 to pull start, need the decompression assembly. Thanks, Pete motoarts at yahooo dawt kawm

Since my front bumper was intact but tweaked, I went ahead and added some scrap pipe and 1" square tubing to the existing piece. The skid plate was mashed, too, so I beat it straight and reinforced the backside with 1/2 L-angle. Rustoleum hammered gray paint finished it off along with the...

Hot rod bling head I...I just can't help myself! While the top end is off, I gutted the head and fired up the die grinder. Ported the seat to bowl transitions, ground the guide bosses down a bit, and hand sanded with 150 grit. May take a stone to them before reassembly just for fun. Deburred...

Need both in/ex shafts. Mine are usable but show some galling. Price shipped to 15068 please. Thanks, Pete motoarts at yahooo dawt kawm