yfz swinger ?

[bones]

so i was reading some builds on E2S and came acrossed a cr500 powered blaster build (http://forums.everything2stroke.com/showthread.php?t=38139) where the guy used the yfz swinger, axle and all and we all know 87warrior917 used the carrier so you should be able to get the sprockets to line up ....so i have a question for anyone with a yfz (or can find out the info) how wide is the swinger at the pivot bolt and what is the over all length??

im sure we have all wondered what it would take to the yfz swinger to fit the warrior

 

[beastlywarrior228]

Yes me too only thing i noticed is the mount for the link is on the bottom

 

[bones]

oh im sure the link will have to customize some how but right im just thinking swinger (one problem that a time)

 

[87warrior917]

Hmm this would be cool as hell! Maybe find a guy on ebay selling a yfz swinger and ask him to measure it for ya? Ive done this many a time to get info like this. Thats how i knew a banshee swinger is to narrow.

 

[bones]

well i have found 2 different measurements 8 11/16 (no end caps) or 9 1/16 (with end caps) ... so anyone have a stoke warrior swinger lying around they could grab a measurement off of

 

[97warrior350]

Im sure 87 does.

 

[DeadLastRacing]

Holesy yit. Thats is a serious build. But not diggin that exhaust at all.

 

[miami1]

Holesy yit. Thats is a serious build. But not diggin that exhaust at all.

he had me up till the exhaust, it looks like hell

 

[bones]

yeah the exhaust looks like $!th

 

[bones]

i know some of you boys can read a type .... i wouldnt even ask if my quad wasnt 45miles away right now

 

[duneracerweston]

stcok warrior swinger is 9.5 without caps 9.75 with caps

 

[bones]

k so that leaves a little room for spacers to get the chain to line up so the next bit of cash i get ill be getting a yfz swinger and working with it on one of my old frames

 

[duneracerweston]

yup should do good how long is the swinger again?

 

[beastlywarrior228]

I wonder what link we can use with it

 

[bones]

dont know the length yet ... im think about a mix of the 450 link and a custom piece to go to the frame

 

[bones]

I wonder what link we can use with it

i was thinking about somthing like what the guy did with the blaster but with more adjustability

 

[87warrior917]

i was thinking about somthing like what the guy did with the blaster but with more adjustability

That looks pretty trick. It'll have to be super strong since the dog bones get hit alot

 

[bones]

so i have still bin researching this and other swing arms

the info i have come up so far is the measurements for the pivot points and lengths on the flowing

yamaha

warrior 350 - no caps = 9 1/2
- with caps = 9 3/4
- gen1 length is 19"
- gen2 length is 18"

yfz450 - no caps = 8 11/16
- with caps = 9 1/16
-length ? from center to center

raptor 660 -with caps = 8 5/8 length 17" 1/2 from ctr to ctr
700r - with caps = 9 3/4
-length 19"
-width from sprocket to rear rotor inside to inside-- 9-3/8(drw) to 9-1/2" (moddedraptor)
-the shock link mount from the ctr of the carrier-- 5-7/8"

honda

450r - with caps = 9 5/16 length 04 - 05 is 18.91 ,06-up is 19.5
400ex - with caps = 9 1/2 length 18"
300ex - with caps = 9 1/2 length 18"
250x - with caps = 9 1/2 length 18"
350x - with caps = 8 5/8 length 20"
250r - with caps = 9 3/8 length 86-87 is 19.5 ,88-89 is 18.5 center to center.

polaris

outlaw - with caps = 9 1/8

kawi

kfx450r - 10 1/16"

if anyone owns or has access to any of these quads plz confirm or correct these measurements

and i would all so like to share a tri-z build i came a crossed that uses a trx450r swinger


http://www.3wheelerworld.com/showthread.php/83904-TRI-Z-450-back-under-the-knife-YTZ450

 

[duneracerweston]

i can confirm the 400ex swingarm numbers! and the 300ex is the same width as the 400ex

you can add that to your data bank

 

[bones]

edited post #18