Search results

Broke Wrist!! After a trip to the emergency room I quite using that type of guard. I just may be unlucky though. I have since used power madd, cyra and tusk with no complaints.

XC Tire I run 21x7x10 Razr2 on the front for excelent steering and braking responce and run 20x11x9 razr on the rear for perdictabilty. there are other tires which offer beter traction but knowing what a tire will do in a corner every time is important, dont belive me look close at the tires xc...

clutch pull Warriors do that a lot!!!! Your clutch is not fully releasing. probably is in the cable adjustment. If you have a ez pull clutch lever this is extreamly common as most of the aftermarket levers are based on Honda geometery. there is a fine ballance where it all works at least till...

herculiner ok I have done this and it held up ok. got dirty bad seems all those little rubber bumps catch dirt who would would have thought it. looks killer on an all flat black bike though. Most of the diy bedlinner needs a painted surface to adhere to. I cleanned and used wet sanding with a...

yfz exhaust I had the same thing happen to me. Was running an old DG, way loud. What I did was get a new take off yfz450 pipe (silencer end) and modify the mounting brackets and add an extension to the warrior head pipe and it all bolted up. welding required and I have a 2+2 axle (the tire...

I have been looking at this for a while. The yfz is 3 inches longer so either you are going to have to stretch the warrior or shorten the yfz plastic. I am planning on shorting the yfz plastic but am still working out the details. Next the yfz seat mounts completely differently and will...

Has anyone run a FCR carb on a warrior? The one used on most 450 class bikes is 39mm which would a little on the large side for all but the biggest stroker motors but the 250 class dirt bikes run a 37mm version and I think it would be right at home on a modified warrior.

There are some which come from the stator on the left side, 3 I think, over the back tire close to the solenoid and some more under the hood. I don’t remember pulling any plastic besides the hood. Also check the ground on the motor along with battery connections

Has anyone had a yfm nikasil cylinder nikasil plated? The stuff seems to work pretty good. I have a 06 yfz I race and 2 years I locked yfz the crank to my surprise the cylinder was still in perfect shape. Many hours of practice and 22 races later is when I had to replace the crank and still did...

Does anyone know if a 366 piston will work with the +4 stroker crank hot rods sells? I am finding conflicting info on this. Has anyone measured the pin height of the piston made for the stroker? The kit is sold with an 84mm and I figure if I am going to bore the cylinder anyway why not go to 86mm.

Chances are good that attempting to fix it will end up being worse than it is now. I have 2 wheels no my warrior with similar problems, they will both hold air for a day or two. I have tried all the snake oil products I could find to get the rims to seal but no luck. I just check the air often...

Does anyone have a hook up with powder coating? Or places to avoid, I am going to have my frame done and don’t want to be dissapinted.

I get my factory stuff from these guys. Good prices and reasonable shipping. http://www.ysppart.com/pages/home/default.aspx

I am a welder by trade and welding aluminum correctly takes the right equipment and lots of practice. If you know a welder who can do it and is willing to dedicate the time it can be done but it will likely be cheaper to get some from PRM. My PRM skids have taken a beating since 1997 and are...

Has anyone used the rappy heel guard with the foot pegs? I am thinking of using them with modified yfz plastic in my warrior project this winter.

Be careful with the torch aluminum gives very little warning before it just goes away. A large hammer generally works but you will probably never get the wheel to seal correctly again. Check out eBay most Yamaha sport quads share the same bolt pattern. I picked up a full set of yfz wheels and...

I had the same problem! Turned out to dirty connectors could not say which ones as after being towed back to camp I had a few adult beverages and began cleaning all the connectors I could find and have not had the problem since! I used carb cleaner and a toothbrush and upon reinstalling them I...

Has anyone retrofitted a smaller diameter rear brake rotor onto a warrior? I have to question Yamaha’s sanity on using a larger brake rotor on the warrior than the banshee. ground clearance is nice and any extra is even better.

I added myself; sorry for the yfz pic but I apparently don’t have any pics of the warrior in this computer. By the way my finish line at this race in the emergency room!

I have been doing a little research and it looks like the raptor 350 linkage is set up differently than the warrior. The raptor 350 rear shock linkage seems to emulate its big brothers and they both have superior rear suspension to the warrior. I have not been on the raptor 350, can anyone...