Search results

Hello friends. Seems like maybe our Warrior atv's are a dying breed? Not much recent activity on this site..... I posted this bike about 1 week ago, on the nmi section. I am hoping a warrior enthusiast will purchase this 1996. I assure you this is NOT a typical dogged out YFM. My...

Hey Guys! Long time no visit here, as I have moved on to utilities-4x4. I do at least stick w/ Yamahas, although a Polaris will show up occasionally @ my house shop for rebuilds...... So, as to the reason for my re-introduction here. My ex bro-in law (who is 60yrs old) built a warrior in...

carb woes Try this-as it starts to sputter, pull the choke. If it piks up rpm, then u know your running lean. If it goes splat faster, overrich. From this info you can start to tune. Good Luck

clutch prob Same happened to me, after a few attemps, heres what we came up with: The pushrod should be flush with cover prior to installing cover. hold it in place with the arm, it should be between the 2 marks on the cover. After all is tightened down, set your actual arm location by...

Hey guys, thanks for all the help in the past. My 02 is up and running, but I need some help on the rear caliper. I have it torn down to rebuild, but since it came to me apart, I need some help on assembly order. I tried the Yamaha schematics, but they dont show how the bracket is situated, nor...

carb If your set screw is all the way in, you are bypassing the idle circuit and into the main. Chek float height, as your fuel level has to reach the pilot. Chek fot trash in your pilot jet. Good luck

Hey guys, needing some recommendations from you on a oil cooler. Either a frame mount or under hood type. So many out there, don t want to spend a bunch of money, something in the 30-50 dollar range. Need one with mounts. I can mock up fittings. Have the adapter and just need some ideas to look...

tips Hey there, Ive rebuilt several top ends and here are some things to keep in mind: Dont buy piston until your jug is measured. you wil probably need at least a first size overbore and the piston has to fit the bore. Find yourself a small eng machine shop that will meaure your bore and...

Engine sorted out I promised to let yall know when I got this 350 (360) sorted out, and what I did was this: pulled the top end back off, sent the cylinder and head to my machinist, who checked all the work he did. Everything checked out. On his suggestion, I bought another replacement set of...

valve seals and addl work Find yourself a local small eng repairshop that does machine work. Remove the head and take them the head and valve seals from your yamaha dealer. My shop charges 36.00 for seating the valves, installing the seals. Basically rebuilding the head. Then all you have to do...

Exc cond crank and rod, off 2001 or 2. Tight and ready to use. 125.00 plus actual ship accept paypal.

Exc condition cases, I think all bearings good. Cleaned a few with parts cleaner and spin smooth. Case has been apart on shelf, no rust. No damage anywhere. 125.00 plus actual ship. Accept paypal

motor smokin after rebuild I cant justify spending all this money and time and accept a smokin motor. The guy who does the machine work Ive used several times and had no prob. Hes lookin @ the head now. Along with the weisco and machine work, I installed a Hot Cams stg 1 cam and new valve...

smoking after rebuild Yea thats what I thought too, in the head. There is no oil in the pipe, as the entire system came from another motor. I have another good head, so I am going to take yalls advice and tear back into it. I was going to just run it, but I went out & started it this am and...

Hey guys, been a while since Ive done a top end on a 350, ive done about 4, and i dont remember any of them smoking after top end. I used the same shop-bored and honed the jug to 1mm over, used the weisco 10 to 1. rebuilt head, new valve seals and valve job. I have not been able to put any load...

Wow Thanks Thanks guys. My son and I are huge yamaha fans. Hes got a Kodiak 450, my ride is an ancient but indestructible 2000 Griz 600. Really looking forward to assembling the Warrior in the garage. Top ends out to the shop. as well as the head. Lots of great info here. Will be watchin...

Hello everyone- New member to your site, but older guy and have owned lots of Yamaha quads. 3 wolvs, 2 griz 600 and a few warriors. Im a single parent so all of the quads ive had are older ones. just got back from our local boat show in louisville and a part of me wishes i could afford a...

more details Sure. Pretty sure all bearings are good, know crank is good. Suspect one shift shaft may need cleaning up or replaced. Have gasket set on order, would need clutch installed-has a good clutch as well. You can email me directly @ [email protected]. Let me know approx cost Mike

Hey guys. Got a 2000 Warrior engine totally dissassembled. I didnt take it apart, so Im clueless about reassembling it. I know it was taken apart due to some type of transmission failure. Ive done lots of top ends, but never split a crankcase before. It appesrs as a low hour tight engine, all...