Search results

Yamaha Raptor 350 & Warrior Forum

Help Support Yamaha Raptor 350 & Warrior Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. M

    exhaust studs broke

    When mine broke they still left a bit sticking out, I just WD-40'd the hell out of them and used vicegrips to unscrew them.
  2. M

    Look what $600 can get you

    Well I finally got a proper cold air intake, now all it needs is O2 sensors and spark plugs. But so far, it's damn fast. Not much power below 3k RPM, but once it hits 4k you better hold on, it gives you a nice kick a 4 and 5k, it's crazy. And the sound... Oh god it's nearly orgasmic, sounds...
  3. M

    Look what $600 can get you

    The regulator is on the airbox side of the front fuel rail, I actually replaced both fuel rails and the regulator with known working ones, that allowed me to actually start it when it warmed up, before it just flooded.
  4. M

    Look what $600 can get you

    If you hear a ticking sound coming from your valve cover don't worry about it, it's a perfectly normal noise for these motors. Also, if anyone still cares, this damn thing still isn't on the road. I towed it over to my cottage to fix the timing belt because there's a garage there, swapped it...
  5. M

    Selling some unneeded stuff

    Bump again, it's been a while.
  6. M

    Carb issues

    Mine was giving me nonstop issues, I replaced the spring, stretched it a bit, replaced the o-ring and it still got stuck. I don't know what's wrong but I just gave up on that carb.
  7. M

    Bogs on whoops

    He said he used the FMF jet kit, are those Mikuni or Dynojet jets? And yea, don't even talk to me about Dynojet, utter useless trash. Not only do they use a completely different sizing scale, their needle doesn't work with Mikuni jets and vice-versa. I had to figure that out from experience...
  8. M

    Bogs on whoops

    Do you have the little plastic thing that goes around the main jet? It keeps fuel from sloshing around too much right under the main jet.
  9. M

    Post your Pumpkins

    Isn't it a dragon? :-/
  10. M

    Hill climbs?

    These quads are really front heavy, so that help immensely with keeping the nose down during hill climbs.
  11. M

    I hate Carbs.......NEED HELP ASAP

    It's in the manual, in the general specs and float adjustment sections, you can't miss it.
  12. M

    Look what $600 can get you

    Woo! Installed the new VAF and it finally runs properly! :D It idles beautifully, but stutters at high RPM, I'm guessing it's the distributor. I already bought a replacement but still haven't installed it. Also, it spits out light, white smoke, hope it's water vapour though because it's been...
  13. M

    Hydroplaning/water skipping

    I've seen some wipeouts from hydroplaning and it looked like it hurt, you either go right into the bars really hard or you just fly off. I did it once at the top of 3rd gear and when I stopped I hit the bars and got completely soaked. :P
  14. M

    Look what $600 can get you

    Well mazda parts are expensive, it sucks I know. A disty cap costs almost $40 here, with a rotor being $20. That's a really weird problem though, and if I learned anything from this car, it's the mazda motors are just too damn fiddly and complicated. AHA! Figured out why the motor's...
  15. M

    Selling some unneeded stuff

    Yes I do, how about $25+shipping?
  16. M

    Look what $600 can get you

    I found a set of bronzoil bushings in the mx3 forums so I'm pretty good for that, all I need is the shifter stabilizer bushings now. That sucks about your car though, did it run badly though? Or was it just throwing codes? And about the idle problem, did you adjust your TPS? Mine had that too...
  17. M

    Look what $600 can get you

    Yes it have VRIS, the actuators are on the left side of the IM, you can see them in front of the blue and white connectors at the back. There are 2 types of ZE: straight neck (popular for you probe/mx6 guys) and curved neck (popular for mx3 guys). It's not the K8 IM, my friend has a K8 mx3...
  18. M

    Look what $600 can get you

    I took it for a quick spin around the block today, and even with a screwed distributor and a few other problems I managed to get a bit of wheelspin in 1st while already going around 10 km/h. :D But wow, the shifter bushings are completely gone, it took me 5 tries to get it into reverse and 3...
  19. M

    2000 warrior battery size?

    When I went to walmart they just had a little booklet there, looked it up and found the right size.
Back
Top