Go Back   YFM350.com Forums > Warrior/Raptor 350 Technical > Instructional Tutorials
Reply
 
Thread Tools Search this Thread Display Modes
Old 05-10-2013, 05:32 PM   #61
duneracerweston
Senior Member
 
duneracerweston's Avatar
 
Join Date: Jan 2011
Location: Brownsboro Texas
Posts: 6,068
Default

Its cast aluminum. It breaks some times. I would bet the pack wasn't together when you tightened it.

Ive ran this for as long as I can remember. Ive never had a problem.

I use driveline performance clutches and love them.

As for wave washers. They will destroy the hub boss. Toss them to decrease the chance of clutch damage
__________________
Elite 2002 SE Walle

DRW PERFOMANCE

http://www.yfm350.com/forums/showthread.php?t=31275

JE, White Brothers, GYT-R, G1P, DRW, SH Design, Sidewinder, KYB, AMP, Maier, DG, ITP, Balistic Performance, CV4, MSR, Moose Racing, Dalton Racing, Mr. Crankshaft, IMS Roll Design, American Star Racing, Lone Star Racing, Speedlinez, ASV, Driveline Performance, Thermotech, JT Racing, Driven Performance, East Coast ATV, ALBA, DuraBlue, Shindy, Kibble White, D.I.D, K&N, OuterWares, Kehine.



Login or Register to Remove Ads
duneracerweston is offline   Reply With Quote
Old 05-11-2013, 03:18 PM   #62
iamdaman
Member
 
Join Date: Apr 2012
Location: Cincinnati, OH
Posts: 33
Default

Quote:
Originally Posted by duneracerweston View Post
Its cast aluminum. It breaks some times. I would bet the pack wasn't together when you tightened it.

Ive ran this for as long as I can remember. Ive never had a problem.

I use driveline performance clutches and love them.

As for wave washers. They will destroy the hub boss. Toss them to decrease the chance of clutch damage
I used a screw driver to keep the pack together before I tightened the springs like it recommends in the Clymer manual. And the wave washers are the little rings labeled as #17 on the diagram, right?
__________________
97 warrior
Bored .030 over?
stage 1 hotcam
Kenda viper rear tires
MSR YZ250 shifter
DG RCM Exhaust
iamdaman is offline   Reply With Quote
Old 05-12-2013, 12:29 PM   #63
WV98YFM350
Senior Member
 
WV98YFM350's Avatar
 
Join Date: Oct 2012
Location: WV
Posts: 630
Default

your prolly better off without the wave washers To be Honest...
__________________
*98 WARRIOR
http://i1341.photobucket.com/albums/...ps621f5923.jpg
Rappy clutch pull, extra clutch steel mod, HD Clutch Springs, 11/40 JT gearing, RK o-ring, Weston saver and rollers, 25" GBC Gator rears, 23" GBC X rex up front, sparky diamond plate skid,valve cap and spring mod, renthal grips, Alba blue PB block off, wiseco timing chain. Also have a sparky torq header and an 01 660 rear shock to install
WV98YFM350 is offline   Reply With Quote
Old 05-12-2013, 02:36 PM   #64
jasonp
Senior Member
 
Join Date: Oct 2006
Location: New Richmond, WI
Posts: 2,385
Send a message via MSN to jasonp
Default

Quote:
Originally Posted by WV98YFM350 View Post
your prolly better off without the wave washers To be Honest...

Yeah you don't really need them. Most guys will leave them out. They just help push the clutch pack (plates) apart...
jasonp is offline   Reply With Quote
Old 07-22-2013, 09:55 PM   #65
04Warrior04
Senior Member
 
04Warrior04's Avatar
 
Join Date: Oct 2010
Location: West Virgina
Posts: 227
Default

Quote:
Originally Posted by iamdaman View Post
I used a screw driver to keep the pack together before I tightened the springs like it recommends in the Clymer manual. And the wave washers are the little rings labeled as #17 on the diagram, right?
Is he right? Is #17 the wave washers?
__________________
04 Warrior: G Force axle, 4" front wheel spacers, Fox high performance ignition, moose rear skid, All around Maxxis Razr 2's, Hmf Slip on, Banshee rear, K&N Filter and precharge.
04Warrior04 is offline   Reply With Quote
Old 05-17-2014, 12:21 AM   #66
happydad08
Member
 
Join Date: Feb 2014
Posts: 31
Default

yes is 17 the wave washers? I am putting a new clutch in tomorrow and want to do this. and I am going to use one of the old steel plates witch one is the thin steel? thanks guys?
happydad08 is offline   Reply With Quote
Old 08-25-2015, 06:51 PM   #67
Glamisrider
Junior Member
 
Join Date: Aug 2015
Posts: 13
Default Thick or thin Steel?

Got an 88 Warrior.

If I remove the 2 wave washer/plates should I add an extra thick or a thin steel to the clutch pack?


Thin Steel is part 10 on the fische: PT#: 168-16325-00-00
Thick Steel is part 11 on the fische: PT#: 3J2-16324-00-00



Thanks
Glamisrider is offline   Reply With Quote
Old 09-08-2015, 02:44 PM   #68
Glamisrider
Junior Member
 
Join Date: Aug 2015
Posts: 13
Default Add 2 Steels?

Well I pulled it apart over the weekend and removed the 2 wave washer/plates. Both of these "wave washers" and they both measured 1.5mm to 1.53mm, which is the same thickness as the thin steel clutch plates (plate #10 int he fiche, PT#: 168-16325-00-00 )

So if I remove the two "Wave washers" and I replace them in the stack with two thin clutch plates so the stack is the same thickness as the original thickness; am I suppose to add an additional steel to that?
OR
Do I just replace the wave washers with two thin steels?


Thanks
Glamisrider is offline   Reply With Quote
Old 09-08-2015, 03:10 PM   #69
2001cheapwarrior
Member
 
Join Date: Apr 2015
Location: North Carolina
Posts: 62
Default

Just pull the wave washers and add one thin steel. Did it last week and it works great. Not sure about adding 2 thin steels.
2001cheapwarrior is offline   Reply With Quote
Old 09-08-2015, 07:07 PM   #70
tcwes8
Senior Member
 
tcwes8's Avatar
 
Join Date: Sep 2014
Location: McDonald PA
Posts: 365
Default

I added a thick steel.

Last edited by tcwes8; 09-08-2015 at 07:22 PM.
tcwes8 is offline   Reply With Quote
Old 09-08-2015, 09:30 PM   #71
Glamisrider
Junior Member
 
Join Date: Aug 2015
Posts: 13
Default

Well when I did it, I pulled both wave washers and added a thick & a think steel.

Since adding two thins would equal out the original thickness, I added a thick and a thin and I am .4mm (.015748 inch (1.5 thousandths) or just under 1/64th of an inch) thicker than the original clutch pack.

The clutch is pretty hard to pull now and I'm not weak, should I be concerned about it being over loaded and possibly breaking under use/load?
Glamisrider is offline   Reply With Quote
Old 09-15-2015, 08:21 AM   #72
Glamisrider
Junior Member
 
Join Date: Aug 2015
Posts: 13
Default

Bump....anybody have an idea if it's safe to run the clutch pack this way?
Glamisrider is offline   Reply With Quote
Old 09-15-2015, 04:36 PM   #73
tcwes8
Senior Member
 
tcwes8's Avatar
 
Join Date: Sep 2014
Location: McDonald PA
Posts: 365
Default

Did you do the raptor clutch mod?
tcwes8 is offline   Reply With Quote
Old 12-21-2015, 07:06 PM   #74
Glamisrider
Junior Member
 
Join Date: Aug 2015
Posts: 13
Default

Quote:
Originally Posted by Glamisrider View Post
Well when I did it, I pulled both wave washers and added a thick & a thin steel.

Since adding two thins would equal out the original thickness, I added a thick and a thin and I am .4mm (.015748 inch (1.5 thousandths) or just under 1/64th of an inch) thicker than the original clutch pack.

I finally got a chance to ride this set up and the clutch kept sticking so I removed the thin steel and it works good now.


So for those of you wondering what to do; remove the two wave washers and add one thick steel clutch plate and it should work good.


Glamisrider is offline   Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -4. The time now is 05:18 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.