Go Back   YFM350.com Forums > Warrior/Raptor 350 Technical > Motor, Transmission, Electrical, Intake & Exhaust
Reply
 
Thread Tools Search this Thread Display Modes
Old 09-28-2017, 12:36 AM   #1
racer jim
Junior Member
 
Join Date: Sep 2017
Location: Brookings, Oregon
Posts: 6
Default i need a stump puller !!

I have a 1988 warrior that I use to tow a 3300# drag race car. I am also using it to maneuver my car trailer. It struggles to start things moving . I have 10/45 sprockets on it now and would like to try a 50 or 55 . Does anyone make the 50 or 55 sprockets? The rear hub is a early design, I think. It has 4 sprocket mounting bolts. Obviously top speed is not a priority. Any help would be appreciated. racer jim



Login or Register to Remove Ads
racer jim is offline   Reply With Quote
Old 09-29-2017, 09:32 AM   #2
bomber315
Senior Member
 
Join Date: Jun 2009
Location: Lucinda, PA
Posts: 824
Default

ok here goes....

so your 4 bolt sprocket hub is holding you back. I compared the axle part number ( 3GD-25381-00-00 ) to other years of warrior and it appears the be the same,

therefore you should be able to get a 6 bolt sprocket hub from another year and open up a new world of sprocket choices

you can double check this info, i just looked it over real fast. I don't completely remember if the sprocket hub goes into the bearing carrier seal or not. You may have to mix and match years (of seals) there to get things to seal up. I'm thinking if you have a drag car tho, this shouldn't be to hard for ya to figure out. Just be advised that the bearing carriers have a different diameter. Therefore if the 6 bolt hub doesn't jive with the seal, you may need to find a "custom" seal that does.

I believe i should have a 6 bolt hub in my collection i can sell if you are interested.

Last edited by bomber315; 10-01-2017 at 11:48 PM. Reason: *SHOULDN'T be too hard for ya
bomber315 is offline   Reply With Quote
Old 09-29-2017, 02:59 PM   #3
racer jim
Junior Member
 
Join Date: Sep 2017
Location: Brookings, Oregon
Posts: 6
Default

bomber315,
Thanks for the response. I needed to get someone with the knowledge and experience to point me in the right direction. I will do some research of the various axle , bearings and hubs to see if I can make that change . I will keep you posted of my progress and if I can use that hub you have in your inventory. racer jim
racer jim is offline   Reply With Quote
Old 09-29-2017, 05:02 PM   #4
racer jim
Junior Member
 
Join Date: Sep 2017
Location: Brookings, Oregon
Posts: 6
Default

bomber315,
I have checked part numbers like you suggested. the part #'s for the axle, bearing and seal for the '88 and the '90 are exactly the same. It appears that a hub change only will be what I need. I show a pn 3GD-25381-00-00 for the hub. Check your spare parts and let me know if this is the one you have. racer jim
racer jim is offline   Reply With Quote
Old 09-29-2017, 05:07 PM   #5
racer jim
Junior Member
 
Join Date: Sep 2017
Location: Brookings, Oregon
Posts: 6
Default

woops!! wrong part # need pn 3GD-25386-00-00.
racer jim is offline   Reply With Quote
Old 10-01-2017, 05:17 PM   #6
racer jim
Junior Member
 
Join Date: Sep 2017
Location: Brookings, Oregon
Posts: 6
Default

bomber315,
I have located a hub here in town and a 56t gear. When I can get them installed and tested I will update this thread. Thanks for the info. racer jim
racer jim is offline   Reply With Quote
Old 10-01-2017, 11:50 PM   #7
bomber315
Senior Member
 
Join Date: Jun 2009
Location: Lucinda, PA
Posts: 824
Default

excellent! glad to help with something out of the ordinary... gives my brain a good little workout
bomber315 is offline   Reply With Quote
Old 11-21-2017, 01:55 AM   #8
racer jim
Junior Member
 
Join Date: Sep 2017
Location: Brookings, Oregon
Posts: 6
Default

bomber315,
I have installed the newer year hub and a 56T gear on my 88 warrior. I works perfectly. All I had to do is notch out the support bracket for the nylon chain support to clear the sprocket teeth and add more links in the chain. Thank you for the lead about checking part numbers. It worked out perfectly. racer jim
racer jim is offline   Reply With Quote
Old 11-21-2017, 05:46 PM   #9
bomber315
Senior Member
 
Join Date: Jun 2009
Location: Lucinda, PA
Posts: 824
Default

excellent man you are welcome


bomber315 is offline   Reply With Quote
Reply



Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -4. The time now is 01:48 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.